16.11.2026

New building block, existing machinery?

2,3-Butanediol as a raw material for engineering polyesters
Ann-Kathrin Ullrich
Exclusive to K-Mag
Liquid brown droplets that look like oil.
© okanakdeniz/ envato images

For decades, the material of choice beneath floor slabs and in inverted roofs has been XPS. The extruded polystyrene rigid foam is pressure-resistant and also insensitive to moisture. PIR and PUR boards (polyisocyanurate and polyurethane) insulate better but perform less well where conditions remain permanently damp. It is precisely this trade-off that EveryCarbon aims to resolve. The company is a spin-off of Hamburg University of Technology (TUHH) and winner of the “Circular Biomanufacturing” challenge run by Germany’s Federal Agency for Breakthrough Innovation (SPRIND).

"ECOne™ is an engineered polyester for tough applications," says co-founder Apolonio Huerta – for example, insulation installed in a damp basement that needs to last for 30 years or more.

What is 2,3-butanediol? A new building block for polyester

The key is a molecule that has so far played hardly any role in plastics production: 2,3-butanediol (2,3-BDO). "That makes development interesting, but also challenging," says Michael Carus, founder of the nova-Institute. One difficulty, he explains, is controlling crystallinity. Prof. Gerrit Luinstra of the University of Hamburg, one of EveryCarbon’s partner institutions, likewise confirms that 2,3-BDO has so far been relatively little studied as a building block for polyesters. One reason, he explains, lies in its chemistry: 2,3-BDO is a so-called secondary diol, and the polyester chemistry of such diols is far less developed than that of established building blocks – much of the know-how gained from PET production, for example, has not yet been applied to them. Before his team’s work, there were also only a few references to high-molecular-weight material. And interest in a new material usually only emerges once a first property profile exists, Luinstra says. "Before that, it is merely the hope of producing something of practical use." EveryCarbon has not publicly disclosed the exact chemical composition or technical data sheet of ECOne™, as it is subject to patent protection. More insight is expected from the first prototype ECOne™ insulation boards – one of the company’s main development areas – which EveryCarbon expects in early 2027.

Processing and recycling: Will the bio-based polyester work on existing production lines?

Apolonio Huerta, CCO of EveryCarbon, and Sebastian Beblawy, CEO of EveryCarbon
Apolonio Huerta, CCO of EveryCarbon, and Sebastian Beblawy, CEO of EveryCarbon // © EveryCarbon

For processors, the key question is whether their existing lines can keep running. "Our customers shouldn’t need new machines to use our resins," says Huerta. According to him, ECOne™ is therefore designed for extrusion, injection moulding and foaming. Whether it will actually run on today’s XPS tandem extrusion lines without modification, however, has not yet been publicly demonstrated. And what happens at the end of its service life? ECOne™ is certainly not meant to be biodegradable, Huerta stresses – after all, it is supposed to last for decades in buildings. "I don’t know anyone who wants to buy a biodegradable house," says Luinstra. Because it is a polyester, Huerta expects ECOne™ to be compatible with established recycling routes – something the team plans to test as part of ECOne™ development. Recycling is also a question of volume, Carus points out: in the case of PLA, for example, volumes are still too small to justify separate collection and sorting.

Bio-based insulation materials: price, approval and life cycle assessment as hurdles

Whether ECOne™ makes it to market therefore depends on more than technology alone. Carus considers the entry of bio-based materials into the insulation market "quite realistic, provided the properties are right". He does, however, add a caveat: "In construction in particular, approvals and established processing methods are major hurdles." Huerta, too, names price, availability and approval as open issues. On price, he is counting on the feedstock: it could be up to 60 times cheaper than conventional biomanufacturing feedstocks, and models point to a route towards price parity with fossil-based diols. "A model isn’t a plant," he cautions, however. According to initial data from EveryCarbon in collaboration with the Fraunhofer IPA, producing the diol cuts CO₂-equivalent emissions by up to 85% compared with equivalent waste management and fossil production routes. A full life cycle assessment is, however, still pending. Huerta cites security of supply as a further argument: the feedstock comes from regional residual streams rather than global petrochemical supply chains.

Plastic from biowaste: Where the carbon comes from

Amber-colored plastic pellets and three test rods made from them on a blue surface—ECOne™, the bio-based polyester from EveryCarbon
© EveryCarbon

That leaves the question of feedstock. Instead of crude oil, the carbon comes from post-consumer food waste and residual streams from agricultural and industrial point sources. Partners first pre-treat these residues to produce a liquid intermediate. A genetically modified microorganism then converts it into 2,3-BDO, which is subsequently polymerised. That every single carbon atom ends up in the product, however, is more the vision behind the company name than a closed carbon balance, Huerta concedes. Depending on the application, he says, the diol is worth up to 80 times more per carbon atom than biogas. Luinstra, however, points to a limitation of bio-based processes: separating the product from the aqueous fermentation broth is almost always energy-intensive. Carus puts the size of this feedstock pool into perspective: organic waste plays an "important but quantitatively limited" role. Perhaps 20 to 30% of biogenic feedstock could come from waste and by-product streams, he estimates, with the bulk coming from primary biomass.

What stands out is how quickly the project has progressed. EveryCarbon is a young company: it was only founded after the team had demonstrated feasibility in the lab during the first year of the SPRIND challenge, which began in November 2023. The focus throughout this period was above all on the production platform – a continuous process that reliably converts mixed waste streams into 2,3-BDO. According to the company, fermentation ran stably for 180 days without contamination or antibiotics, even as the composition of the waste changed. "So far we haven’t found a condition where impurities from the waste shut the process down," says Huerta. In addition, the team built a container-based pilot plant on the site of a wastewater treatment plant in Stuttgart and is developing digital monitoring and automation for the next scale-up stage.

ECOne™ builds on this platform. Market entry, however, is still some way off, as the pilot plant currently holds only 100 litres. As a next step, EveryCarbon therefore plans to produce in rented fermentation facilities of 10 cubic metres and more. The first prototype insulation board is expected in early 2027, and from 2027 development partners will be able to receive samples. Even before that, interested organisations can request early access to the ECOne™ technical data sheet “directly from us”, Huerta says, in order to assess potential applications. Later on, the company plans to build its own plant with a capacity of around 30,000 tonnes of diols per year. In the longer term, Luinstra also sees a further route: 2,3-BDO can be converted via butadiene into styrene – a building block for bio-based polystyrene. Using 2,3-butanediol from waste thus opens up a new bio-based raw material pathway for polyesters. Whether ECOne™ will replace XPS, however, remains to be seen: test data, fire safety data, approvals and a competitive price have yet to be demonstrated. Huerta nevertheless remains optimistic: "We are excited to keep demonstrating the opportunity behind ECOne™ and to bring it to market together with partners in the near future."

Key Takeaway:

PIR and PUR boards: Rigid foam insulation boards based on polyisocyanurate (PIR) or polyurethane (PUR). They insulate very well but are more sensitive than XPS where conditions remain permanently damp.

XPS tandem extrusion line: Two extruders connected in series: the first melts the polystyrene and mixes in the blowing agent, the second cools the melt before it expands into boards.

Diols: Alcohols with two hydroxyl groups (–OH). They react with dicarboxylic acids to form polyesters. One example is 2,3-butanediol.

Author: Ann-Kathrin Ullrich | K-Mag

Ann-Kathrin Ullrich enjoys explaining how new ideas from research, technology and industry are changing everyday life. Alongside her work for EuroShop-Mag, she focuses on plastics and rubber in K-Mag: from new materials and processing methods through to testing technology and issues relating to the circular economy.